EN ISO 20471 is the international standard for high-visibility clothing worn where workers must be seen by drivers and machine operators. It sets how much fluorescent material and retro-reflective tape a garment needs, which colours count, and how the garment is classed. If you buy or sell hi-vis vests, jackets, shirts or trousers for Europe, the UK and many other markets, this is the standard your customers will name.
This guide explains the three classes, the material areas behind them, how garments combine, and what to put in your specification when you order.
What the standard covers
EN ISO 20471:2013 (with amendment A1:2016) applies to garments meant to make the wearer visible in any light, by day and under vehicle headlights at night. It sets requirements for:
- Background material: the fluorescent fabric that makes the wearer stand out in daylight. Only fluorescent yellow, fluorescent orange-red and fluorescent red are allowed.
- Retro-reflective material: the tape that returns light to its source, such as car headlights, so the wearer is seen in the dark.
- Design: where the material sits. Bands must go around the torso, and bands on sleeves and legs must go all the way round.
- Performance after use: colour, reflectivity and dimensions must hold up after the number of wash cycles stated on the label.
Class 1, 2 and 3: the minimum areas
The class depends on the visible area of each material. Class 3 gives the most visibility and is required for the highest-risk work, such as on motorways and airport aprons.
| Class | Fluorescent background (min.) | Retro-reflective tape (min.) | Typical garments |
|---|---|---|---|
| Class 3 | 0.80 m² | 0.20 m² | Long-sleeve jackets, coveralls, jacket + trouser combinations |
| Class 2 | 0.50 m² | 0.13 m² | Most vests, short-sleeve shirts, trousers |
| Class 1 | 0.14 m² | 0.10 m² | Harnesses, some trousers and small garments |
A Class 3 garment must also cover the torso and have either sleeves with tape bands or full-length legs with tape bands. A sleeveless vest therefore usually reaches Class 2, however much material it carries. The class is shown next to the hi-vis pictogram on the label.
Combining garments
Two garments worn together can reach a higher class than either alone. A Class 2 jacket worn with Class 1 or Class 2 trousers can make a Class 3 combination, provided the combined areas meet the Class 3 minimums and the combination was tested and labelled that way. This matters when you build a uniform: specify the whole outfit, not just each piece, if your customer needs Class 3.
Logos, prints and pockets
Anything placed on the fluorescent fabric reduces the visible background area. A large printed logo, an extra patch pocket or a contrasting panel can push a garment below its class. When you add branding, ask your manufacturer to check that the remaining background area still meets the class you need, and keep logos off the reflective bands.
Other markets
- United States: ANSI/ISEA 107 uses garment types (O, R, P) and classes 1–3 with its own minimum areas in square inches.
- Australia and New Zealand: AS/NZS 4602.1 classes garments for day (D), night (N) or day/night (D/N) use.
The materials are similar, but the rules differ, so a garment built for one standard is not automatically compliant with another. Tell your supplier which market the garments are for.
What to put in your specification
- The standard and class: for example “EN ISO 20471 Class 2”.
- Background colour: fluorescent yellow or orange-red, and any contrast colour for two-tone designs.
- Tape: width (usually 50 mm), type (glass-bead or micro-prismatic, sewn or heat-applied), and layout.
- Fabric: polyester knit or mesh for vests; heavier polyester or poly-cotton for jackets and trousers.
- Branding: logo size and position, kept clear of the tape.
- Size range and the wash cycles the label must state.
- Documents: ask which certificates and test reports apply to the exact model you are buying.
Hi-vis products from Gratex Industries
We make hi-vis safety vests, hi-vis jackets, hi-vis shirts and hi-vis trousers in Sialkot, Pakistan, from 25 pieces per style. Popular styles include the zip-front safety vest with reflective tape, the two-tone hi-vis vest and the quilted winter hi-vis jacket.
Tell us the standard and class your customers require and we will confirm the fabric, tape and layout before sampling. For the documents that apply to each model, see our certificates page, or read more about us as a workwear manufacturer.